Mercedes C-Class

W203 since 2000 of release

Repair and car operation



Mercedes-Benz
+ Mercedes-Benz Cars of a class C (W-203)
+ Operation manual
+ Routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   - Leaving and external equipment of a body
      General information and security measures at carrying out body works
      Cleaning and leaving
      Repair of insignificant damages of body panels
      Repair of considerable damages of a body
      Windscreen damages as a result of hit of stones
      Replacement of brushes of screen wipers
      Removal and installation of a jet of a stekloomyvatel of a windscreen
      Removal and installation of a jet of back glass
      Removal and installation of the lever of a screen wiper of a windscreen
      Removal and installation of the lever of a back screen wiper
      Removal and catchment basin installation
      Removal and cowl installation
      Removal and installation of facing of a cowl
      Cowl adjustment
      Removal and installation of the lock of a cowl
      Detachment of a cable of a drive from the cowl lock
      Removal and installation of a lattice of a spoiler
      Removal and bumper installation
      Removal and installation of a rear bumper
      Removal and installation of a forward wing
      Removal and installation of a protective level on a wing
      Removal and installation of a protective level on a bumper
      Removal and installation of a protective level on a door
      Removal and installation of a forward loker covered
      Removal and installation of a back part of a loker of a wing
      Removal and installation of a forward door
      Door adjustment
      Removal and installation of forward facing of a door
      Removal and installation of a triangular slip
      Removal and installation of the external handle of a door
      Removal and installation of facing of an external rear-view mirror
      Removal and installation of an external mirror
      Removal and installation of glass of a mirror
      Removal and trunk lid installation
      Removal and installation of facing of a trunk lid
      Removal and installation of a clamp of the lock of a luggage carrier
      Removal and installation of the lock of a door of a back
      Removal and installation of the mechanism of the lock of a door of a back
      Removal and installation of the cylinder of the lock of a luggage carrier and back door
      Removal and installation of a door of a back
      Adjustment of a door of a back
      Removal and installation of facing of a door of a back
      Removal and installation of facing of a door of a back
      Removal and installation of a back spoiler
      Removal and installation of a cap of a cargo compartment
   + salon Equipment
+ Onboard electric equipment






Removal and installation of a forward loker covered

Loker of a wing consists of three parts.


Forward loker

Removal

 PERFORMANCE ORDER

1. Lift a forward part of the car and establish it on supports.

Operation of lifting and car installation on supports is connected with danger! Therefore before carrying out operation familiarize with Poddomkrachivaniye's Section and Introduction towage to the management.


2. Turn out 3 bolts of fastening (1) and take out razzhimny a clip (2).

3. Take out 4 razzhimny clips (1) of a front bumper.

4. Take out a forward loker of a wing from a wheel arch.


Installation

 PERFORMANCE ORDER

1. Installation is carried out in sequence, return to removal.
2. Lower the car on wheels.


Top and back parts of a loker of a wing

Removal

 PERFORMANCE ORDER

1. Mark with paint the provision of the corresponding forward wheel concerning a nave. It will allow to establish at assembly an otbalansirovanny wheel in its former situation. Weaken bolts of fastening of a wheel before a car poddomkrachivaniye. Lift a forward part of the car, put it on supports and remove a forward wheel.

Operation of lifting and car installation on supports is connected with danger! Therefore before carrying out operation familiarize with Poddomkrachivaniye's Section and Introduction towage to the management.

2. Remove a forward part of a loker of a wing.

3. Turn out bolts and plastic nuts (shooters on an illustration).

For an element of a back part of a loker it is necessary to turn out one bolt and one nut on the bottom.


4. Take out back (1) and the top (2) elements of a loker of a wing from a wheel arch. The back element is necessary for taking out under a cover on the bottom.


Installation

 PERFORMANCE ORDER

1. Installation is carried out in sequence, return to removal.
2. Establish into place a forward wheel so that the marks put at removal coincided. Previously grease with a thin layer of bearing greasing aligning belt of a disk of a wheel on a nave. Bolts of fastening of a wheel do not grease. Rusty bolts replace. Wrap bolts. Lower the car on wheels and tighten bolts cross-wise the moment 110Нм.