Mercedes C-Class

W203 since 2000 of release

Repair and car operation



Mercedes-Benz
+ Mercedes-Benz Cars of a class C (W-203)
+ Operation manual
+ Routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   - Leaving and external equipment of a body
      General information and security measures at carrying out body works
      Cleaning and leaving
      Repair of insignificant damages of body panels
      Repair of considerable damages of a body
      Windscreen damages as a result of hit of stones
      Replacement of brushes of screen wipers
      Removal and installation of a jet of a stekloomyvatel of a windscreen
      Removal and installation of a jet of back glass
      Removal and installation of the lever of a screen wiper of a windscreen
      Removal and installation of the lever of a back screen wiper
      Removal and catchment basin installation
      Removal and cowl installation
      Removal and installation of facing of a cowl
      Cowl adjustment
      Removal and installation of the lock of a cowl
      Detachment of a cable of a drive from the cowl lock
      Removal and installation of a lattice of a spoiler
      Removal and bumper installation
      Removal and installation of a rear bumper
      Removal and installation of a forward wing
      Removal and installation of a protective level on a wing
      Removal and installation of a protective level on a bumper
      Removal and installation of a protective level on a door
      Removal and installation of a forward loker covered
      Removal and installation of a back part of a loker of a wing
      Removal and installation of a forward door
      Door adjustment
      Removal and installation of forward facing of a door
      Removal and installation of a triangular slip
      Removal and installation of the external handle of a door
      Removal and installation of facing of an external rear-view mirror
      Removal and installation of an external mirror
      Removal and installation of glass of a mirror
      Removal and trunk lid installation
      Removal and installation of facing of a trunk lid
      Removal and installation of a clamp of the lock of a luggage carrier
      Removal and installation of the lock of a door of a back
      Removal and installation of the mechanism of the lock of a door of a back
      Removal and installation of the cylinder of the lock of a luggage carrier and back door
      Removal and installation of a door of a back
      Adjustment of a door of a back
      Removal and installation of facing of a door of a back
      Removal and installation of facing of a door of a back
      Removal and installation of a back spoiler
      Removal and installation of a cap of a cargo compartment
   + salon Equipment
+ Onboard electric equipment







Removal and installation of the lever of a back screen wiper

Versatile person

Removal

 PERFORMANCE ORDER

1. Moisten back glass with water.
2. Start for short time a screen wiper and stop it the switch. Thus the cleaner comes to extreme situation.
3. Mark the provision of a brush at correctly adjusted levers on glass, for example, with a sticky tape.

4. Cast away a cap (1) and unscrew a nut (2).

5. Cast away the lever (3) and remove it.

 Thus do not damage a jet inserted into an axis of a cleaner.


Installation

 PERFORMANCE ORDER

1. Be convinced that the electric motor of a screen wiper is in extreme situation. If necessary start the electric motor for short time and stop the switch.
2. Establish the screen wiper lever on an axis and expose on a mark put with a sticky tape at removal.
3. Screw a nut (2).
4. Once again check extreme position of levers. For this purpose close a cowl, moisten glass with water and for short time start a screen wiper. Levers should return to the established situation and glass should not fall outside the limits at purification of glass.
5. If necessary once again unscrew nuts and repeat adjustment.
6. Fix a nut (2) moment 12Нм and put on a cap.