Mercedes C-Class

W203 since 2000 of release

Repair and car operation



Mercedes-Benz
+ Mercedes-Benz Cars of a class C (W-203)
+ Operation manual
+ Routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   - Leaving and external equipment of a body
      General information and security measures at carrying out body works
      Cleaning and leaving
      Repair of insignificant damages of body panels
      Repair of considerable damages of a body
      Windscreen damages as a result of hit of stones
      Replacement of brushes of screen wipers
      Removal and installation of a jet of a stekloomyvatel of a windscreen
      Removal and installation of a jet of back glass
      Removal and installation of the lever of a screen wiper of a windscreen
      Removal and installation of the lever of a back screen wiper
      Removal and catchment basin installation
      Removal and cowl installation
      Removal and installation of facing of a cowl
      Cowl adjustment
      Removal and installation of the lock of a cowl
      Detachment of a cable of a drive from the cowl lock
      Removal and installation of a lattice of a spoiler
      Removal and bumper installation
      Removal and installation of a rear bumper
      Removal and installation of a forward wing
      Removal and installation of a protective level on a wing
      Removal and installation of a protective level on a bumper
      Removal and installation of a protective level on a door
      Removal and installation of a forward loker covered
      Removal and installation of a back part of a loker of a wing
      Removal and installation of a forward door
      Door adjustment
      Removal and installation of forward facing of a door
      Removal and installation of a triangular slip
      Removal and installation of the external handle of a door
      Removal and installation of facing of an external rear-view mirror
      Removal and installation of an external mirror
      Removal and installation of glass of a mirror
      Removal and trunk lid installation
      Removal and installation of facing of a trunk lid
      Removal and installation of a clamp of the lock of a luggage carrier
      Removal and installation of the lock of a door of a back
      Removal and installation of the mechanism of the lock of a door of a back
      Removal and installation of the cylinder of the lock of a luggage carrier and back door
      Removal and installation of a door of a back
      Adjustment of a door of a back
      Removal and installation of facing of a door of a back
      Removal and installation of facing of a door of a back
      Removal and installation of a back spoiler
      Removal and installation of a cap of a cargo compartment
   + salon Equipment
+ Onboard electric equipment







Removal and cowl installation

Removal

 PERFORMANCE ORDER

1. Open a cowl and establish it vertically.
2. Remove a lattice of a forward spoiler, address to appropriate section.
3. Disunite the socket of a heater of a jet of a stekloomyvatel and remove hoses from a jet as it is described in the Section Removal and installation of a jet of a stekloomyvatel of a windscreen.
4. If the solar sensor is established, disunite its socket located under a lattice of ventilation.
5. Disconnect wires from holders on a cowl.
6. For simplification of the subsequent installation of a cowl mark with a felt-tip pen the provision of its loops.

For removal of a gas-filled emphasis ask the assistant to take a cowl. Otherwise a cowl упадёт since cannot be kept by one emphasis.


7. Disconnect a gas-filled emphasis from a spherical support on a cowl and remove. For this purpose raise a screw-driver a lock ring of an emphasis (the shooter on an illustration) a little. The second emphasis remove similarly.

8. Turn out fastening screws (arrows on an illustration) and remove a cowl by means of the assistant. Before an otvorachivaniye of screws of fastening of loops put a rag between a cowl and a body for protection against damages of a paint and varnish covering.

9. Put a cowl on a reliable lining.


Installation

 PERFORMANCE ORDER

1. Put a cowl into place by means of the assistant and fix screws, without tightening them.
2. Close a cowl and check a gap on prileganiye perimeter, if necessary adjust.
3. Tighten screws of fastening the moment 8Нм.
4. Establish one gas-filled emphasis on a spherical support and insert a lock ring. Similarly establish the second emphasis.