Mercedes C-Class

1. Do not weaken and do not remove cables from plugs of the storage battery at the working engine. Otherwise electronic elements (for example, the generator) can be damaged.
2. Switch off everything consumers of the electric power. At first disconnect and remove minus, and then the plusovy plug.
3. After a detachment of plugs of the storage battery the electronic key in the lock of ignition does not turn any more, and the lever of the AT selector remains blocked in the situation "R".

1. At first connect plusovy, and then the minus plug.
2. After connection of the storage battery it is necessary to carry out the following works:

· Installation of hours (Undressed the Multipurpose steering wheel, the universal display).
· Introduction in memory of a code of a radio receiver (see. «Operation manual on a radio receiver»).
· A repeated adjustment of lateral glasses (Undressed Window regulators, the roof hatch).
· A repeated adjustment of the shifted and lifted top hatch (Undressed Window regulators, the roof hatch).
· Repeated adjustment of ESP system. For this purpose a steering wheel at the working engine turn from an emphasis against the stop.

1. Care of the battery is very important procedure, allowing to avoid stops in a way because of its discharge. Performance of procedure of service needs the corresponding tool.
2. Before the beginning of procedure of service always at first switch off the engine and disconnect all electrodevices, then disconnect a weight cable from the battery.

If the radio receiver of your car is equipped with system of protection against theft, make sure that you gathered the correct code before a battery detachment.

3. Usually cars are equipped with the batteries which are not demanding special leaving. It is possible to remove covers a banok and to add the distilled water. Latest models can be equipped with the batteries which not are not demanding leaving which are completely sealed.

4. Remove covers and check electrolit level in each of a battery banok. It should be above plates. Usually on everyone bank there is a level index. If level of electrolit is lower than norm, add only the distilled water and then close covers a banok.

Overflow can lead a banok to electrolit transfusion during the accelerated charging that will cause corrosion and damage of the next to the battery a component.

5. If the positive plug and a collar of a wire of the battery of your car are equipped with a rubber protector, make sure that it is not torn and not damaged. It should close the plug completely.
6. It is necessary to examine periodically an external condition of the battery on existence of such damages, as cracks in the case.
7. Check reliability of a tightening of collars of wires of the battery, providing good electric connection. Check each of wires on all length on existence of cracks and attritions of isolation and wires.
8. At detection of traces of corrosion (usually representing a friable raid of white color) disconnect wires from plugs, smooth out them a special brush and again connect. Emergence of corrosion can be minimized by installation of specially processed washers which are available on sale in shops of auto parts, or by drawing on plugs and collars of wires of a layer of acid-free vaseline or suitable greasing after their connection.
9. Make sure that the pallet of the battery is in a satisfactory condition, and the bolt of a fixing collar is reliably tightened. If the battery acted in film from the pallet, track, that in an installation time on it details or other extraneous subjects did not lie. At a latching of a fixing collar do not tighten its bolt too hardly.
10. Corrosion traces from the pallet, cases of the battery and surrounding surfaces can be removed by means of water solution of baking soda. Put a mix with a small brush, let's to it stand and then wash away plentiful quantity at its finest.
11. The metal surfaces of the car which have undergone corrosion, it is necessary to cover with a first coat on a zinc basis and then to paint.
12. Additional information on the battery and on engine start from an external source can be found in Chapter 5 and in Introduction.

1. Remove all covers about a battery banok (if they are available) and close openings pure rags to prevent an electrolit spillage. Disconnect a cable of weight of the battery and connect charger wires to its plugs (positive to positive, negative to negative), then turn on the charger in a network. If it has the switch, make sure that it is established in situation of «12 volts».

If the radio receiver of your car is equipped with system of protection against theft, make sure that you gathered the correct code before a battery detachment.

2. If you use the charger with a current more than two amperes, regularly check the battery during a charging to make sure that it did not overheat. Using the slow charger, you can quietly leave the battery to be charged on all night long after regular check within the first two hours. At a charging of the batteries which are not demanding leaving, certain precautionary measures (for example, use of very nizkoamperny charger) can be demanded. On such battery can be precautionary шильдик but if it is not present address for consultation in representation office of the manufacturer or to the electrician of a repair truck.
3. If banks of the battery have the demountable covers, each hour within the last several hours of a charging cycle check electrolit density by means of the areometer. Inexpensive areometers are available on sale in shops of auto parts - at their application follow enclosed instructions. It is possible to consider the battery charged if within two hours indicators of density of its electrolit do not change, and the electrolit in banks freely bubbles. The electrolit density in separate banks should be almost identical. If this not so, means, one or several banok of the battery failed and it is necessary to replace them.
4. Some batteries not demanding leaving have above built-in areometer having a window - the color indicator of degree of a charging of the battery. The usually brightly painted window means that the battery is completely charged, and dark color testifies to need of an additional charging. More exact data are given in the instruction of the manufacturer of the battery.
5. If the battery is sealed and has no built-in areometer, you can check charging degree by means of connected to plugs of the battery of the digital voltmeter. Completely charged battery will show 12.6 and more than a volts.
6. Fuller information on the battery and on engine start from an auxiliary source can be found in Head Electric equipment of the engine and in Introduction.